horizontal steam generator caculation

Product thermal capacity: 4-35 t/h
Working pressure: 1.0-2.5 MPA
Outlet temperature:: 184-350 ℃
Available fuel: Bituminous coal, lean coal, anthracite
Available industries: Heating, chemical, food, tobacco, textile, print and dyeing, feed, medicine, building materials, wine, hospital

>Motor Sizing Calculatio

Motor Sizing Calculations

2019-11-15 · Motor Sizing. Proper sizing and selection of a motor for your equipment is key to ensuring performance, reliability and cost of the equipment. In addition to the information below for properly sizing a motor, Oriental Motor offers online motor sizing tools as well as

Get A Quote

>Application amp; Installation Guide Engine Room Ventilati

Application amp; Installation Guide Engine Room Ventilation

2019-9-4 · Engine Room Ventilation This guide addresses engine room ventilation considerations that apply to the successful installation, operation and maintenance of Cat engines, generator sets, compressor units, and other packaged units. The primary aspects of a properly designed engine room ventilation system are cooling air and combustion air.

Get A Quote

>steam generater frp crushing recovery line-

steam generater frp crushing recovery line- K

Steam generator types Oilfired. These burned diesel fuel, which is a lightweight fuel oil. The term steam generator (as opposed to boiler) usually refers to an automated unit with a long spiral tube that water is pumped through and is surrounded by flame and hot gases, with steam issuing at the output end.

Get A Quote

MATHEMATICAL MODEL TO CALCULATE TH

MATHEMATICAL MODEL TO CALCULATE THE

2016-4-12 · horizontal axis wind turbines. However, wind power absorption efficiency of vertical axis wind turbines is much less, so it is important to assess the capacity of the wind turbine. This article describes mathematical model to calculate the performance of low power vertical axis wind turbine. Index Terms- Mathematical Model, Power Factor, Swept

Get A Quote

>Pipe Flow-Friction Factor Calculations with Exc

Pipe Flow-Friction Factor Calculations with Excel

2015-8-5 · Pipe Flow-Friction Factor Calculations with Excel Harlan H. Bengtson, PhD, P.E. COURSE CONTENT 1. Introduction Several kinds of pipe flow calculations can be made with the Darcy-Weisbach equation and the Moody friction factor. These calculations can be conveniently carried out with an Excel spreadsheet. Many of the

Get A Quote

>Tank Calibration Chart Calculator - O'Day Equipme

Tank Calibration Chart Calculator - O'Day Equipment

From fiberglass to steel tanks, we have a tank calculator to help you with your petroleum needs. Learn more from O'Day Equipment.

Get A Quote

>()Unisim Solution Overview.p

()Unisim Solution Overview.ppt

()Unisim Solution Overview.ppt,UnisimSuiteSolutionOverviewHoneywellOTSUniSimTMSuiteUniSimTMSuiteUniSimTMSuiteUniSimDesignSuite-

Get A Quote

>Heat Transfer in Refrigerator Condensers and Evaporato

Heat Transfer in Refrigerator Condensers and Evaporators

Heat Transfer in Refrigerator Condensers and Evaporators D. M. Admiraal and C. W. Bullard ACRCTR-48 For additional information: Air Conditioning and Refrigeration Center University of Illinois Mechanical amp; Industrial Engineering Dept. 1206 West Green Street Urbana, IL 61801 (217) 333-3115 August 1993 Prepared as part of ACRC Project 12

Get A Quote

>Pipe Sizing Steam Supply andCondensateReturn Lin

Pipe Sizing Steam Supply andCondensateReturn Lines

2006-12-6 · Pipe Sizing Steam Supply and Condensate Return Lines Definitions Steam mains or mains carry steam from the boiler to an area in which multiple steam-using units are installed. Steam branch lines take steam from steam main to steam-heated unit. Trap discharge lines move condensate and flash steam from the trap to a return line.

Get A Quote

>Pump Power Calculator - Engineering ToolB

Pump Power Calculator - Engineering ToolBox

2019-11-29 · Hydraulic Pump Power. The ideal hydraulic power to drive a pump depends on. the mass flow rate the; liquid density; the differential height - either it is the static lift from one height to an other or the total head loss component of the system - and can be calculated like. P h(kW) = q ρ g h / (3.6 10 6) = q p / (3.6 10 6) (1) where

Get A Quote

>MECHANICAL EXHAUST VENTILATION SYSTEMS FO

MECHANICAL EXHAUST VENTILATION SYSTEMS FOR

2019-11-27 · horizontal distance not less than six inches beyond the outer edges of the cooking surface. C. Compensating Hood – A hood that has an outside air-supply with air delivered below or within the hood. Where makeup air is diffused directly into the exhaust within the hood steam, heat, and products of combustion, and where grease or smoke is

Get A Quote
Contact us
Tel

0086-510-68530066

Chat online

Online message


Gas-fired(oil-fired) boilers
Coal-fired boilers
Biomass-fired boilers
Thermal oil heaters
Hot water:0.7-14 MW
14.1-21 MW
21.1-29 MW
29.1-75 MW
Steam :  1-10 t/h
11-20 t/h
21-90 t/h
91-140 t/h